Lumenier LUX HD AIO F7 FC + 50A BLHeli_32 2-6S ESC

The Lumenier LUX HD AIO F7 Flight Controller + ESC is DJI HD system ready with an onboard 9v regulator to power the DJI Air Unit in a simple plug-and-play configuration. It uses a powerful F7 processor along with top-of-the-line hardware from the 50A BLHeli_32 2-6s. Unleash the capabilities of your FPV Racing Quadcopter with the Lumenier LUX HD AIO F7 Flight Controller! This LUX HD AIO F7 comes in a standard 30.5x3.5 form factor weighing only 16.6g.

The LUX HD AIO F7 builds on all the best features of its predecessors and further improves on hardware components and layout, and is now dedicated to a design for the DJI digital HD system.

You get a whopping 6x dedicated UART ports with built-in inversion for peripherals. This Flight Controller features 1 onboard LC VBAT filtered power pad designed to power your DJI Air Unit at 9v and also other 5v accessories. The onboard 5v 3A regulator can be used to power the camera, Rx, and LEDs all at the same time, while the dedicated 9v 2A regulator reliably powers the DJI Air Unit or Vista system.

Check out all our Flight Controllers and the rest of our Lumenier Products!

Features

• Supports DSHOT 1200, Proshot, Oneshot125 (125-250us), Oneshot42(41.7-83.3us), and Multishot (5-25us). Auto-detection.
• Synchronous rectification technology adds efficiency, damped light
• New F3 MCU running at 108MHz, (older ESCs use F0 at 48MHz)
• Adaptive timing, compatible with a wide range of motors and Kv
• Built-in 5v regulator that powers the LED system
• Powerful regenerative braking / active braking.
• BEC: 9v 3A cont. (for DJI HD System)
• MCU: 216MHz STM32F722RET6
• Anti-Vibration silicone grommets
• Input: 8.4~25.2V (2~6S LiPo)
• 6 Uarts with built-in inversion
• 2-6s LiPo battery compatible
• WS2812 Led Strip support
• Beeper solder pad
• BEC: 5V 3A cont.
• LC Power Filter
• IMU: MPU6000

Software/Hardware Features

• Direct Plug and Play with DJI Air Unit or Caddx Vista
• BLHeli passthrough flashing supported by hardware
• Betaflight support - target LUXF7HD

Specifications

• Mounting Holes: 30.5mm square to the center of holes
• Dimensions: 38x38x5mm (includes USB in height)
• USB C connector for programming
• High quality, gold plated PCB
• Dimensions: 39x45x5mm
• Constant: 50 Amps
• Input: 2-6s LiPoly
• Burst: 60 Amps
• Weight: 16.6g

Includes

• 1x Lumenier LUX HD AIO F7 FC + 50A BLHeli_32 2-6S ESC 
• 1x 8pin (5 wire) micro JST-GH 8cm connector for DJI Air Unit
• 4x Anti-vibration silicone grommets (for M3 sized screws)
• 8x M3x8mm threaded hex plastic spacer
• 4x M3x35mm black oxide steel screws
• 4x M3x25mm black oxide steel screws
• 8x M3 silicone grommet insert (White)
• 4x M3 silicone grommet insert (Black)
• 1x 1000uF Low ESR Capacitor
• 1x set of mounting hardware
• 8x M3 plastic hex nuts
• 4x M3 rubber o-rings