A flight controller with a built-in Serial ELRS receiver and 4-IN-1 Blheli_S 12A ESC specially developed for Digital HD FPV, which removes the analog OSD chip 7456, optimizes the PCB layout, and supports 1-2S Lipo/LiHV lithium batteries, very Suitable for Digital HD Tinywhoop/Cinewhoop/Toothpick and other small FPV drones. The flight controller uses the F405 chip, supports Betaflight/INAV firmware, has 3 sets of complete UARTs available, and integrates a BMP280 barometer and 8Mbp blackbox, which greatly enhances the playability of the flight controller.
Check out all our Flight Controllers and the rest of our HappyModel Express LRS Products!
Only the v1.0 version of the CrazyF405 flight controller has silk screen printing errors, and the V1.1 and V2.0 versions have been fixed
Specifications:
- Brand Name: Happymodel
- Item Name: CrazyF405HD ELRS 1-2S AIO Flight controller
- Mount size: 25.5mmx25.5mm
- Weight: 4.8g without power lead wire
- Firmware target: BetaflightF4
- Support 1-2s Lipo/LiHV battery
Flight controller
- MCU: STM32F405RGT6 (168MHZ, 1Mbyte FLASH)
- GYRO Sensor: BMI270 (SPI connection)
- Mount hole size: 25.5mm*25.5mm
- Power supply: 1-2S battery input (DC 2.9V-8.7V)
- Built-in 12A(each) Blheli_S 4in1 ESC
- Built-in Serial ExpressLRS 2.4GBuilt-in BMP280 Barometer
- Built-in 8MBp blackbox
- Built-in voltage meter sensor , voltage meter scale 110Built-in current meter sensor , current meter scale 470
Onboard 4in1 ESC
- Power supply: 1-2S LiPo/LiPo HV
- Current: 12A continuous peak 15A (3 seconds)
- Support BLHeli_S Bluejay firmware
- Factory firmware: Bluejay ESC V0.19Firmware target: Z-H-30
- Default protocol: DSHOT300
- When use 1s battery and high KV 0702/0802 motors, should set startup power to 1100/1200
Onboard UART ExpressLRS 2.4GHz Receiver
- Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
- RF Frequency: 2.4GHz
- Antenna: enameled copper wire 31mm length
- Telemetry output Power: <12dBm
- Default firmware version: ExpressLRS V3.0.1
- Firmware target: HappyModel EP1/2 2400 RX
- Could update firmware via ExpressLRS configurator
Usage Instructions:
If bound to radio but having trouble seeing stick movement in Betaflight, then you may need to turn off the "Model Match" factory setting in the ELRS web GUI.
For original factory 4.3.2 version firmware, if you want to use BMP280 barometer, please connect to betaflight configurator and then move to CLI command, then type the following command:
resource I2C_SCL 2 B10
resource I2C_SDA 2 B11
set baro_bustype = I2C
set baro_i2c_device = 2
save
If you upgrade the firmware to 4.4.2 and want to use BMP280 barometer, please add BPM280 support to custom defines, following the procedure:
1. Enable expert mode on firmware flasher tab
2. Add BARO_BMP280 to custom defines
3. Flash the board
4.Configure resources for external BARO device for the flight controller in CLl:
resource I2C_SCL 2 B10
resource I2C_SDA 2 B11
set baro_bustype = I2C
set baro_i2c_device = 2
save
Package Includes:
- 1x Happymodel CrazyF401 Whoop AIO Flight Controller with 12A BLHELI_S 4-in-1 ESC and ELRS 2.4GHz Rx
- 1x Power lead with a XT30 Connector
Warranty Policy:
If any defect, warranty, or troubleshooting needs should arise for this product, please be aware that Happymodel requires pilots to reach out to them directly.
We must follow the policies set by this manufacturer in order to carry their products.
Please make sure to contact them directly if you feel your HM product is defective in any way. If they are not able to help you fix the problem, then they will have us issue you a return shipping label to return the defect, and allow us to send you a replacement.
Happymodel support email: info@happymodel.cn
