The Holybro Kakute H7 Mini is a Flight Controller full of features including onboard VTX ON/OFF Pit Switch with battery voltage, HD System/VTX & 4in1 ESC plugs, barometer, OSD, 6x UARTs, easy soldering layout and much more.
The Kakute H7 Mini builds upon the best features of its F7 predecessor and further improves on hardware components and layout. HD ready, it has an easy plug to power HD system like Caddx Vista while supporting analog system. It features an onboard “VTX ON/OFF Pit Switch” that allows you to completely power off the video transmitter using a switch on your RC transmitter. Great if you are working on your drone, waiting for the GPS to get a fix, getting ready for a race while preventing it from overheating or interfering with others flying.
It has 6x dedicated UART ports with built-in inversion for peripherals, 4in1 ESC plug, and x8 compatible with M5-M8 Signal Pads, allowing easy support for x8 Octocopter configuration. The integrated BetaFlight OSD makes it easy to display important information on your FPV display like battery voltage, flight time, warnings, RSSI, smart audio features and more. It is also ready for autonomous flight with the on-board barometer. There are LED & buzzer pad, I2C pad (SDA & SCL) for external GPS/Magnetometers.
Version 1.3 has 1Gb Nand-Flash memory & BMI270 instead of MPU6000
Checkout all our 20x20mm Flight Controllers, 20x20 Stacks and the rest of our Holybro Collection!
Kakute H7 Mini Flight Controller Specifications:
- Input Voltage: 2-6S
- MCU - STM32H743 32-bit processor running at 480 MHz
- IMU - BMI270
- Barometer - BMP280
- OSD - AT7456E
- 6x UARTs (1,2,3,4,6,7)
- 9x PWM Outputs (8 Motor Output, 1 LED)
- 1 x JST-SH1.0_8pin port (4in1 ESCs)
- 1x JST-GH1.0_6pin port (For HD System like Caddx Vista & Air Unit)
- BEC: 5V 2A Cont.
- Mounting: 20x20mm/Φ3.6mm hole with ΦM3 and M2 Grommets
- Dimension: 31x30x6mm
-
Weight: 5.5g
Tekko32 AM32 4-In-1 mini 50A ESC Features:
- All new High-quality MOSFETs with low internal resistance & heat generation, and individual metal heatsink
- New and faster F4 MCU @ 150Mhz (compared to F3 @108Mhz & F0
@48Mhz)
- Separate drive & control circuit, reducing the electrical interference to the control circuit
Tekko32 F4 4-In-1 mini 50A ESC Specifications:
- Continuous current: 50A x4
- Burst current: 60A x4
- Battery support: 4-6S
-
PWM frequency: 8k to 96k
- Support DShot 150/300/600/1200
- Support MultiShot/OneShot/Proshot/PWM, etc.
-
ESC telemetry Support
-
Onboard analog current sensor
- AM32 Firmware
- 1000uf 35v capacitor included
- Mounting holes: 3.8mm @ 20x20mm, compatible with either M2& M3 Rubber Gourmet (Included)
-
Dimensions: 46.6x38x6mm / Weight: 15.6g
Atlatl HV micro:
Features:
- Compatible with all major FPV receivers from vendors such as Fatshark, ImmersionRC, etc.
- Supports the standard 40-channel set: band A, B, E, Fatshark, and Raceband.
- SmartAudio input allows remote control by the flight controller. Change channel, transmit power, and more from Betaflight OSD, flight controller USB port, Taranis Lua Script, and more.
- All parameters are controllable via push-button on the side of the unit, for cases where SmartAudio is not used.
- MMCX connector is durable and easy to use. Rated for 100’s of mating cycles. Easy and quick antenna changes. No more ripped-off UFL connectors.
- LED indicators for channel, band, and power. Allows easy check of vTX parameters simply by glancing at the quad.
- Variable transmit power from 25 mW to 800 mW. Use 25 mW for a race and then easily switch to 800 mW for freestyle.
- 0.5 mW True Pit Mode allows you to power up safely without the risk of knocking other pilots out of the air.
- Built in microphone, so you can listen to your motors while you fly, no matter how far away you fly.
- Standard 26mm form factor allows you to mount the Atlatl directly on your flight controller stack.
Specifications:
- Output Power: 0.5 mW (pit mode), 25 mW, 200 mW, 500 mW, 800 mW
- Audio: 6.5 MHz Mono
- Protocol?smart audio2.0
- Antenna Connector: MMCX
- Input Voltage: 7 to 28 volts (2-6S LiPo)
- Dimensions: 30x26mm
- Mounting Holes: Standard 20mm square to center of holes (M3)
- Weight: 3.6g
Package Includes:
- 1 x Kakute H7 Mini STACK
- 1 x Electrolytic capacito: 1000uF 35v
- 1 x JST SH 8pin to 8pin 65mm cable
- 1 x JST SH 8pin to 8pin 25mm cable
- 1 x JST SH 6pin 150mm cable
- 1 x JST SH 6pin to GH 8pin 150mm cable
- 1 x JST SH 6pin to GH 8pin 80mm cable
- 1 x 80mm SMA--MMCX Cable
- 1 x 60mm Antenna
- 1 x 150mm 4pin JST GH wire
Laws and requirements regarding transmission of radio waves vary greatly across the world.
In some countries, this product may not be legal. In the USA, the operator of this product is required by law to have a
HAM amateur radio license, at the very least.
It is the operator's responsibility to make sure that they are using this product in a legal manner, or not using it at all if not possible to do legally in their location.
By adding this product to your cart, you are confirming that you have read this notice, and that Pyrodrone is in no way responsible for the actions of the operator while using this product.
