(PRE-ORDER) Happymodel Mobula6 ECO 2024 1S 65mm HDZero ELRS 2.4GHz Ultra Light Micro FPV Whoop - BNF

Shipping ETA Mid to Late April

Happymodel Mobula 6 ECO 2024 is the first BNF that uses HDZero ECO Bundle.

HDZero ECO Bundle is designed to bring digital FPV to more pilots by offering a low cost, light weight, and durable alternative to analog video. The digital video signal has stable color reproduction and 720p progressive scan video with the low latency HDZero is known for.

This budget-friendly Air Unit is a groundbreaking product—it’s the first VTX/camera combination that utilizes a HD composite video signal, eliminating the need for a delicate MIPI cable.

The ECO FPV System was meticulously designed for ultra-lightweight drones like Tiny Whoops, where every fraction of a gram counts. The camera’s huge 98deg vertical FOV is perfect for fast indoor proximity flying. The ECO VTX weighs approximately 4.5g, while the camera (including wires) comes in at about 1.6g. With the included 0.2g dipole antenna, the entire Eco Bundle weighs about mere 6.3g in total.

Check out our collection of Micro BNF/RTF/PNP Whoops and the rest of our  Happymodel Products!

Features:

• AIO Flight controller with Serial ELRS Receiver
• Compatible with HDZERO system
• Equipment with the lightest brushless motors-SE0702 only 1.49gram
• HDZERO NEW ECO VTX and Camera ready
• Smooth and powerful
• Compatible for 1S Lipo/LIHV
• Onboard blackbox read

Specifications:

• Brand Name: HAPPYMODEL & HDZERO CO-Brand
• Model: Mobula6 ECO 2024
• Frame wheelbase: 65mm
• Weight: 23.16 gram without battery
• Size: 81mm*81mm*45mm
• Compatible with 1S Lipo battery or Lihv battery
• Battery Plug: GNB A30

Motor：

• Mode: SE0702 KV28000
• Configu-ration:9N12P
• Stator Diamter:7mm
• Stator Length:2mm
• Shaft Diameter:Φ1mm
• Motor Dimension(Dia.*Len):Φ9.5mm*14mm
• Weight(g):1.49g
• No.of Cells(Lipo):1S only

Propellers：

• Materials: PC
• Inch: 31mm
• Pitch: 0.8 in
• Weight: 0.21g
• Mount hole diameter: 1mm

Flight controller：

• SuperX HD ELRS
• Betaflight 4.4.2 firmware ready
• Firmware target: CRAZYBEEF4DX
• MCU:STM32F411CEU6 (100MHz, 512K FLASH)
• Sensor: BMI270 or ICM42688P (SPI connection)
• Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
• Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
• Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
• Bluejay ESC Firmware ready
• Built-in 5V 1A BEC
• Built-in voltage detection
• No betaflight analog osd chip

Onboard 4in1 ESC：

• Power supply: 1-2S LiPo/LiPo HV
• Current: 12A continuous peak 15A (3 seconds)
• Support ESC-Configurator and BLHELI_S Suite configurator
• Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
• Default protocol: DSHOT300

Onboard Serial ExpressLRS receiver：

• RF Frequency: 2.4GHz
• Antenna: enameled copper wire 31mm length
• Telemetry output Power: <12dBm
• Receiver protocol: CRSF
• Default firmware version: ExpressLRS V3.0.1
• The same hardware with Happymodel EP1 receiver
• Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through

HDZERO ECO VTX:

• Composite HD Video interface
• 1S-3S Input
• 25mW/200mW RF output
• 25.5×25.2 M2 soft mounting
• Antenna Retention
• 32.4×32.5mm (29x29mm inner)
• 4.5grames/4mm Thickness (w/o shielding)

HDZERO ECO Camera:

• Image Sensor : 1/3”
• Resolution: 720@60fps 4:3
• LENS: FOV D:150° H:120° V:98°
• Shutter: Rolling Shutter
• Net Weight: 1.6g (With Cable)
• Dimensions: L14mm*W14mm*H13mm

Package Includes:

• 1x Mobula6 2024 1S 65mm whoop Drone Frame +Canopy
• 1x SuperX HD ELRS AIO flight controller
• 1x HDZero ECO VTX
• 1x HDZero ECO Camera
• 4x SE0702 KV28000 brushless motor
• 1x Gemfan 1208-3 31mm tri-blade propellers(4cw+4ccw)
• 1x Spare Canopy
• 1x Screw Driver
• 1x Propeller disassemble tool