Product Details
The AOS 5 EVO is a lightweight drone designed with low-vibration technology. This drone features state-of-the-art electronics and topology optimization. The AOS 5 EVO allows you to run less filtering, with less associated delay, and increase your PID gains far higher than any other frame in its weight class. Get ready for the most responsive 5" quad you have ever flown!
Changelog:
July 13, 2023: Updated with silicone dampppers and Secured Battery Plug with Anti-Spark Filter
Check out all our Digital BNF/PNP/RTFs and the rest of our AOS Products!
HIGHLIGHTS:
- DJI O3 HD Air Unit Low-Latency Digital Transmission
- Topology-optimized truss design arms
- 2.5mm Top and Bottom Plates
- Optimized Camera Protection
- 32x32 GoPro Mounting
- Built by iFlight
- 5" BNF Drone
- Low Vibration
Vibrations limit performance
As a pilot I often struggled with Jello, mid-throttle oscillations and propwash handling on my 5 inch freestyle mini quads. As an aerothermal engineer I realized that the issue lay in the vibration and resonance performance of the quadcopter frame itself.
Even the cleanest motors and props produce large amounts of vibration in flight. These vibrations excite the resonant modes of the frame amplifying vibrations at certain frequencies, increasing their amplitude and energy. These vibrations pass into the gyro and create noise on the signal. This noise requires additional filtering, which adds latency, and limits maximum PID gains through motor heating.
Modern flight firmware: Betaflight 4.3, KISS Ultra, and FETTEC all benefit enormously from a low vibration airframe. The AOS 5 O3 allows you to run less filtering, with less associated delay, and increase your PID gains far higher than any other frame in it's weight class. Get ready for the most responsive 5" quad you have ever flown.
Harmonic analysis, topology optimization.
I used Blackbox logging and harmonic analysis to visualize the vibrations of the AOS 5 O3 during the design process. For the O3 I combined this with topology optimization to tune the geometry of each part of the frame, moving the frame resonances up and away from the motor frequencies and separating them as far as possible. This avoids, as far as possible, the situation where the motor frequencies match a frame resonant frequency and so amplification is minimized.
As a result, you can run less filtering. Every layer of filtering adds delay that’s mathematically related to how effectively it removes vibrations. This delay prevents the flight controller from responding rapidly enough to propwash leading to poor propwash handling. Reducing the amount of filtering is the best way to improve propwash handling. With the AOS 5 O3 you’ll be in the best possible position to reduce your filtering to an absolute minimum.
Another advantage of lower noise is the ability to run higher PID gains. Higher PID gains allow the quad to track your stick movements with less delay and more precision. The result is greater confidence, particularly when flying tight lines where fast reactions are vital.
Top and bottom plates
The 2.5mm thick main plate supports up to three full-sized 30.5mm stacks. 20 and 25.5mm stacks are supported and the M2 20mm holes are designed to be easily drilled out to M3 if required.
The top plate has pressnuts installed for effortless GoPro mounting using the AOS standard 32x32mm footprint.
The cut outs in the top and bottom plate of the AOS 5 O3 are optimized to preserve as much of the bending and torsional stiffness of the plate as possible whilst minimizing weight.
Arms
The AOS 5 O3 uses a topology optimized truss design for the arms. This truss design provides enormous torsional stiffness, resolving a key source of vibration in traditional frames. It also allows two particularly harmful resonant modes to be individually modified to separate them in frequency.
Truss structures are inherently very strong as they convert bending loads into compression and tension in the individual members. Carbon is much stronger in pure tension and compression than in bending. The 3 screw motor mounting reduces weight and removes the motor hole that can be a stress riser for compressive failure in hard crashes.
Y-shaped motor protectors minimize the risk of damage to those expensive components. Should you ever need to replace an arm, there are only two screws to undo and neither are shared with your electronics.
Camera Protection
The AOS 5 O3 uses 2.5mm Carbon Plates to hold and protect the camera. These are stiffer, lighter and cheaper to replace than aluminum or titanium.
The camera plates include 2 standoffs to maximize durability and a cutout pattern that supports DJI O3 and all typical19-20mm FPV cameras.
Go Pro Mount
The AOS 5 O3 has 32x32 mm M3 mounting holes for 3D printed mounts for your HD camera. Press-nuts in the top plate make installing the mount a breeze.
You can download an STL for the mount shown HERE.
Specifications:
- FC: BLITZ F722
- ESC: BLITZ E45 55A 4-IN-1 ESC
- Video Transmission: DJI O3 Air Unit
- Frame: 255mm wheelbase
- Motor: XING2 2207 motors
- Prop: Nazgul 5 inch propellers
- Takeoff Weight：Approx. 1000 g
- Dimensions (L×W×H)：175×135×32.5 mm
- Max Speed：130 Km/h (Manual Mode)
- Maximum Takeoff Altitude：5000 m
- Max Hover Time：Approx. 8 mins
- Max Flight Distance：5 km
- Max Wind Speed Resistance：130 Km/H (Level 4)
- Operating Temperature Range：-10° to 40° C (14° to 104° F)
- Antennas: 1 Antenna
- GNSS：N/A
Package Includes:
- 1 x AOS 5 O3 5" HD 6S FPV Freestyle Drone W/ DJI O3 FPV System BNF/PNP - Chosen Receiver
- 2 x Propeller Set
- 2 x Antenna
- 2 x Battery Pad
Note:
All iFlight BNFs are tested before shipment to guarantee the highest quality.
Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!
To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"
Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!
Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.
