Skip to content
Holiday Shipping - All Orders Ship Same Day Monday to Friday Before 5PM PST
SAME DAY SHIPPING M-F TILL 5PM PST
Wishlist Pyro Points
TBS Lucid H7 FC 2-8S Dual Camera Input ICM42688 x 2 (duo gyro) Flight Controller - 30x30mm

TBS Lucid H7 FC 2-8S Dual Camera Input ICM42688 x 2 (duo gyro) Flight Controller - 30x30mm

SKU 76B-13833
Availability:
in stock
$59.95 - $59.95
$59.95
$59.95 - $59.95
$59.95


The TBS Lucid H7 FC is a powerhouse built for those who crave peak performance and adaptability in their drones. Whether you're ripping through freestyle moves or fine-tuning a racing rig, the TBS Lucid H7 delivers with its robust 480MHz processor and seamless support for Betaflight, ArduPilot, and INAV. Featuring dual camera inputs, DJI FPV OSD compatibility, and a compact design, it fits effortlessly into any setup. Designed for both seasoned pros and enthusiastic newcomers, this flight controller makes pushing the limits of your drone easier than ever.

Check out all our 30x30mm Flight Controllers and the rest of our TBS products!

Specifications:

    • MCU: STM32H743VIH6 running at 480MHz, with 1MB RAM and 2MB Flash.
    • Gyro: ICM42688 x 2 (duo gyro)
    • OSD Chip: AT7456E (SPI2)
    • Barometer: Infineon DPS310 connected via I2C2.
    • PWM Outputs: 13 channels, including a dedicated “LED” pad.
    • Blackbox (BB): Data logging equipped with a MicroSD card slot (SDIO)
    • UARTs: 7 total (1, 2, 3, 4, 6, 7, 8) signal inversion ready
    • I2C Buses: 2 available.
    • CAN Bus: 1 available.
    • Analog Inputs: 6 ADC channels (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2).
    • LED Indicators: 3 LEDs (Blue, Green for FC Status, Red for 3.3V Power).
    • Breakout: SPI3 breakout available.
    • USB Interface: Type-C connector (USB 2.0 standard).
    • JST Connectors: 
      • 1x JST-SH1.0 8-pin (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
      • 1x JST-GH1.25 4-pin (5V/CAN-H/CAN-L/Ground).
    • Dual Camera Input: Switchable inputs for two cameras.
    • Power Control: Switch for filtered 5V/Vbat output power.
    • DJI FPV OSD: Compatible via any spare UART port.

    Power Specifications

    • Input Voltage: 6 - 36V (2 to 8S LiPo).
    • BEC: 5V 2A continuous (3A max) & 9V 2A continuous (3A max)
    • LDO 3.3V: Supports up to 200mA.
    • Voltage Support: ADC Vbat2 pad supports up to 36V (1K:10K voltage divider).
    • Power Consumption: 200mA @ 5V with Betaflight, 150mA @ 5V with ArduPilot.

    FC Firmware Targets

    • ArduPilot: tba
    • BetaFlight: tba
    • INAV: tba

    Package Includes:

    • TBS Lucid H7 FC
    • FC-to-ESC cable (plug & play)
    • DJI O3 cable (plug & play)
    • 4pcs M3 rubber dampers
    • 4pcs M3x8 screws

 

Warranty Policy:

If any warranty needs for this product arise, please note that the manufacturer of this product is one of the few manufacturers we carry that requests the end user to contact them directly for any troubleshooting or possibly defective items. We must follow these policies set by these manufacturers. Please make sure to contact them directly if you feel your product is defective in any way. Reach out to us if you need an email address or contact link for this manufacturer.


>

Compare products

{"one"=>"Select 2 or 3 items to compare", "other"=>"{{ count }} of 3 items selected"}

Select first item to compare

Select second item to compare

Select third item to compare

Compare