Product Details
The Happymodel Mobula 6 HDZero 1S Whoop is the very first 65mm HD brushless whoop in the world, weighing less than 23.5 grams! The Mobula6 is a smooth and agile brushless drone that comes with the HDZero Nano Lite Camera, EX0802 KV19000 Motors, and many other cool features and specs that make this whoop a must-have! Happymodel has teamed up with HDZero, Runcam, Nick Burns, Mr. Shutterbug, Ryan Quellet, and many other enthusiasts to here to make the dream come true! This whoop comes with Built-In ELRS V3!
Note: Batteries are not included.
Recommended battery: 300~350mAh with BT2.0 or A30 connector cabled
Battery options: CNHL Pizza 350mAh LiHV BT2.0
Dogcom 300mAh LiHV BT2.0
UART ELRS V3.0 ready
Battery Plug: GNB A30 (Compatible with BT2.0)
Onboard black box ready
Default factory dump file:
dump file for Mobula6 HDZERO 1S 65mm digital HD brushless whoop V3
Check out our Micro Whoop Drones and our entire Happymodel Collection!
Specifications
Flight controller SuperX HD ELRS
- Betaflight 4.4.2 firmware ready
- Firmware target: CRAZYBEEF4DX
- MCU:STM32F411CEU6 (100MHz, 512K FLASH)
- Sensor: BMI270 or ICM42688P (SPI connection)
- Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
- Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
- Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
- Bluejay ESC Firmware ready
- Built-in 5V 1A BEC
- Built-in voltage detection
- No betaflight analog osd chip
Onboard 4in1 ESC
- Power supply: 1-2S LiPo/LiPo HV
- Current: 12A continuous peak 15A (3 seconds)
- Support ESC-Configurator and BLHELI_S Suite configurator
- Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
- Default protocol: DSHOT300
Onboard UART ExpressLRS 2.4GHz Receiver
- RF Frequency: 2.4GHz
- Antenna: enameled copper wire 31mm length
- Telemetry output Power: <12dBm
- Receiver protocol: CRSF
- Default firmware version: ExpressLRS V3.0.1
- The same hardware with Happymodel EP1 receiver
- Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through
Motor
- Mode: EX0802 19000KV
- Configu-ration:9N12P
- Stator Diamter:8mm
- Stator Length:2mm
- Shaft Diameter:Φ1mm
- Motor Dimension(Dia.xLen):Φ10.5mmx14.9mm
- Weight(g):1.7g
- No.of Cells(Lipo):1S only
Propeller Gemfan 1219 Bi-blades
- Weight:0.19g
- Material: PC
- Pitch:1 inchProps Dia:30mm
- Center Hole Dia:1mm
HDZero Nano Lite Camera
- 14x16x11 mm
- 1.5gram
- 0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
- Excellent low light performance
- Fov:
- 4:3: D:130° H:108° v:84°
- 16:9:D:122° H:108° V:65°
HDZero Whoop Lite VTX
- 1S Input
- 25mW/200mW RF Output-SmartAudio Support
- 25.5×25.5 M2 Soft Mounting- Antenna Retention
- Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
- 4.5grams/4mm Thickness (without shielding)
Links
Includes
- 1x Happymodel Mobula6 HDZero 1S Whoop
- 1x Gemfan 1210 31mm Propeller (Set of 4)
- 1x Propeller disassemble tool
- 1x Spare Canopy
- 1x Screwdriver
Warranty Policy:
If any defect, warranty, or troubleshooting needs should arise for this product, please be aware that Happymodel requires pilots to reach out to them directly. We must follow the policies set by this manufacturer in order to carry their products. Please make sure to contact them directly if you feel your HM product is defective in any way. If they are not able to help you fix the problem, then they will have us issue you a return shipping label to return the defect, and allow us to send you a replacement. Happymodel support email: info@happymodel.cn
