Product Details
ExpressLRS is currently the most popular remote control link system. It has the characteristics of low latency and high packet rate, and its link quality is very reliable. Now we are about to release Mobula6 equipped with ExpressLRS RC link system, the new Mobula6 elrs would coming out with a new 0702 brushless motor, that would be the lightest brushless motors all over the world. We’re sure this would be a good option for you in the Tiny Whoop Season.
Check out our Mobula 6 and Parts collection and our entire HappyModel selection!
Description:
- Brand: Happymodel
- Item Name: Mobula6 ELRS 1S 65mm Brushless whoop drone BNF version
- Wheelbase: 65mm
- Size: 80mm*80mm*37mm
- Weight: 18.7g
- Voltage:1S
Specifications:
Motor
- Mode: SE0702 KV26000
- Configu-ration:9N12P
- Stator Diamter:7mm
- Stator Length:2mm
- Shaft Diameter:Φ1mm
- Motor Dimension(Dia.*Len):Φ9.5mm*14mm
- Weight(g):1.46g
- No.of Cells(Lipo):1S only
Propellers:
- HQprop31mmx2
- Center Thickness:5mm
- Prop Disk Diameter:31mm
- Center Hole Inner diameter:1.0mm
- Weight:0.2g
Flight controller:
- ELRS F4 2G4 flight controller built-in SPI expresslrs 2.4G receiver
- CrazyF4 ELRS flight controller built-in 915MHz expresslrs receiver
- CrazyF4 ELRS flight controller built-in 868MHz expresslrs receiver
- MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
- Sensor: MPU-6000(SPI connection)
- Board size: 28.5 * 28.5MM
- Power supply: 1S battery input (DC 2.9V-4.35V)
- Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
- Built-in Betaflight OSD(SPI Control)
- Built-in 5.8G VTX
- Built-in ExpressLRS 2.4G/915MHz/868MHz receiver
- Built-in 5V 1A BEC
- Built-in voltage detection
Onboard 4in1 ESC:
- MCU upgraded to EFM8BB21
- Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds)
- Support BLHeliSuite programmable
- Factory firmware: O_H_5_REV16_7.HEX
- Default protocol: DSHOT600
Onboard SPI ExpressLRS 2.4GHz Receiver (Optional):
- Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
- RF Frequency: 2.4GHzAntenna : SMD antenna
- Telemetry output Power: <12dBmReceiver protocol: SPI ExpressLRS
- Could bind with Happymodel ES24TX , ES24TX Lite, ES24TX Slim and DIY 2.4GHz ELRS TX module ExpressLRS version 1.0.0 or 1.0.1 both compatible
Onboard Serial-based ELRS Receiver ( Optional):
- Operation current: ~100Ma
- Rx To FC protocol: CSRF
- Antenna connector: IPEX4
- Telemetry output Power: <17dBmFirmware target: Happymodel_RX_ES915RXReceiver protocol: CRSF
- Could bind with Happymodel ES915TX , Frsky R9M and DIY ELRS TX module(need to flash the same version ELRS firmware)
- Firmware flash via Betaflight pass-through
Onboard 5.8g VTX:
- Output power: 25mw~200mw
- Frequency: 40CH
- Input voltage: 3.3V 5.5V
- Current consumption: 300mA(type)
- Frequency: 5.8GHz 5bands 40 channels
- With Race bandSmartaudio ready
Runcam Nano3:
- Model: RunCam Nano 3
- Image Sensor: 1/3″ CMOS
- Horizontal Resolution: 800TVL
- Lens : 2.1mm(M8) FOV 160°
- Signal System: PAL/NTSC Non Switchable
- S/N Ratio: >50dB
- Electronic Shutter Speed: Auto
- Auto Gain Control (AGC): Auto
- Min. Illumination: 0.01Lux@1.2F
- D-WDR: Auto
- Day/Night: Color
- Power:DC 3-5.5V
- Current: 110mA@5V 120mA@3.3V
- Housing Material: ABS
- Net Weight: 1.2g
- Dimensions: L14mm*W14mm*H9mm
Lipo Battery:
- Capacity:300mAh
- Voltage:3.8v
- Continuous Discharge Rate: 30C
- Size: 57mmx12mmx7mm
- Weight: 8gConnector: PH2.0
Package Includes:
1x Mobula6 1S 65mm whoop Drone Frame
4x SE0702 KV26000 brushless motor
1x HQPROP 31mm bi-blade propellers(4cw+4ccw)
1x Runcam Nano3 1/3 CMOS 800TVL camera
1x Onboard 5.8G 25mw~200mw VTX
4x 1S 300mah 30C LiHV Battery
1x 1S Lipo/LIHV USB Charger
1x Propeller disassemble tool
1x ELRS F4 2G4 flight controller built-in receiver
