Pyrodrone F4OSD-Furling Stack Combo

Regular price $54.99 Sale

Availability: Available Unavailable

Product SKU: 6069

Please read the following carefully regarding the wire harness of this combo!The Furling ESC includes a harness cable with one end already pinned and the other and without connector.User will have to pin the FC end with the provided harness...

Product Details

Please read the following carefully regarding the wire harness of this combo!
The Furling ESC includes a harness cable with one end already pinned and the other and without connector.
User will have to pin the FC end with the provided harness and connector.
It is very important to pay extra attention to which side is plugged to the FC!
both ends use 8 pin connector which means there is a chance the harness can be plugged reversed.
If the harness is plugged reversed it will DAMAGE the FC permanently!

This combo comes with the new Pyrodrone F4 OSD V2 with integrated VTX PIT mode.

Version 2 Update:
The Pyrodrone F4 OSD has a new feature!
VTX Pit mode compatibilty.

In order to use this feature jump the two pads with solder on the "PIT" side ( If this feature is not needed then just jump the pads of the "ON" side and your VTX will always be on)
After you jump the PIT pads connect to Betaflight and go to CLI page , type in the following commands:

resource PINIO 1 A14
set pinio_box = 39,0,0,0
type "save" and then hit enter.

Wait for the FC to reboot, then go to the "MODES" tab in Betaflight and set VTX PIT MODE to an AUX channel you prefer

Done! :-)
F4 OSD Specs.

MPU6000 Gyro
STM32F405 CPUE @ 168mhz, can be overclocked
2-6S direct battery input 
3.3V 100ma, 5V 1.2A BEC
5V Camera Power
Built in configurable Betaflight OSD
Flat bottom PCB for SUPER CLEAN builds
36x36 PCB with 30.5x30.5 mounting holes
6 UARTS. UART1 (INVERTER FOR SBUS),
          UART2 (FREE),
                  UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off 
                  UART4 (Free),
                  UART5 (Smart Audio)
                  UART6 (Free)
 
Built in 4 IN 1 ESC socket(including ESC telemetry, External current sensor)
Plug and plug with the most popular 4-in-1 ESCs (HobbyWing, Airbot, Spedix, Aikon),with supplied cables
Built in solder pads mirror of the 4-in-1 ESC socket
Printed layout instructions ON the board - no need for instructions!

Airbot Furling 45AMP 4in1
Disclaimer: The Furling 4in1 sold by Airbot come with F3 processor.
The batch that we received and pairing with our F4OSD FC as a combo comes with F051 processor.
Please ignore the part where it shows F3 processor in the actual manual that you will receive with the ESC.
Also the Processor has NOTHING to do with the AMP rating of the ESC.


Features:

  • 32bit ESC with BLHELI32 firmware
  • Supports 3-6S lipo input
  • PWM input, TLM supported
  • Voltage output (VBAT)
  • NO BEC
  • Supports oneshot / Multishot / Dshot PWM
  • Mounting holes 30.5x30.5mm
  • Supports damped light
  • Extra Cap needed for high current or 6s usage

    ESC package includes:

  • 1 x Furling 4in1 ESC
  • 1 x 14AWG cable set 
  • 1 x XT60H connector
  • 1 x Copper Tape
  • 1 x Wire harness
  • 2 x 35V 470uF Capacitors
    Loading...

    Your cart

    x