The Happymodel Mobula 6 HDZero 1S Whoop is the very first 65mm HD brushless whoop in the world, weighing less than 23.5 grams! The Mobula6 is a smooth and agile brushless drone that comes with the HDZero Nano Lite Camera, EX0802 KV19000 Motors, and many other cool features and specs that make this whoop a must-have! Happymodel has teamed up with HDZero, Runcam, Nick Burns, Mr. Shutterbug, Ryan Quellet, and many other enthusiasts to here to make the dream come true! This whoop comes with Built-In ELRS V3!

Note: Batteries are not included.

Recommended battery: 300~350mAh with BT2.0 or A30 connector cabled

Battery options: CNHL Pizza 350mAh LiHV BT2.0
Dogcom 300mAh LiHV BT2.0

UART ELRS V3.0 ready
Battery Plug: GNB A30 (Compatible with BT2.0)
Onboard black box ready

Default factory dump file:

dump file for Mobula6 HDZERO 1S 65mm digital HD brushless whoop V3

Check out our Micro Whoop Drones and our entire Happymodel Collection!

Specifications

Flight controller SuperX HD ELRS

Betaflight 4.4.2 firmware ready
Firmware target: CRAZYBEEF4DX
MCU:STM32F411CEU6 (100MHz, 512K FLASH)
Sensor: BMI270 or ICM42688P (SPI connection)
Power supply: 1-2S Lipo Lihv battery input (DC 2.8V~8.7V), only support 1s input for this drone
Built-in 12A(each) Blheli_S 4in1 ESC Dshot300 read
Built-in UART elrs receiver , elrs v3.0 ready, support WIFI and pass-through firmware update
Bluejay ESC Firmware ready
Built-in 5V 1A BEC
Built-in voltage detection
No betaflight analog osd chip

Onboard 4in1 ESC

Power supply: 1-2S LiPo/LiPo HV
Current: 12A continuous peak 15A (3 seconds)
Support ESC-Configurator and BLHELI_S Suite configurator
Factory firmware: Z-H-30 – Bluejay, 0.19, 48kHz
Default protocol: DSHOT300

Onboard UART ExpressLRS 2.4GHz Receiver

RF Frequency: 2.4GHz
Antenna: enameled copper wire 31mm length
Telemetry output Power: <12dBm
Receiver protocol: CRSF
Default firmware version: ExpressLRS V3.0.1
The same hardware with Happymodel EP1 receiver
Could update firmware via ExpressLRS configurator or WIFI or Betaflight pass-through

Motor

Mode: EX0802 19000KV
Configu-ration:9N12P
Stator Diamter:8mm
Stator Length:2mm
Shaft Diameter:Φ1mm
Motor Dimension(Dia.xLen):Φ10.5mmx14.9mm
Weight(g):1.7g
No.of Cells(Lipo):1S only

Propeller Gemfan 1219 Bi-blades

Weight:0.19g
Material: PC
Pitch:1 inchProps Dia:30mm
Center Hole Dia:1mm

HDZero Nano Lite Camera

14x16x11 mm
1.5gram
0.5 inch, up to 10650 mV/Lux-sec ultra-high sensitive CMos sensor
Excellent low light performance
Fov:
4:3: D:130° H:108° v:84°
16:9:D:122° H:108° V:65°

HDZero Whoop Lite VTX

1S Input
25mW/200mW RF Output-SmartAudio Support
25.5×25.5 M2 Soft Mounting- Antenna Retention
Removable Shielding Box- 32.5×32.5mm(29x29mm inner)
4.5grams/4mm Thickness (without shielding)

Links

ELRS Mobula6 HDZero Manual

Includes

1x Happymodel Mobula6 HDZero 1S Whoop
1x Gemfan 1210 31mm Propeller (Set of 4)
1x Propeller disassemble tool
1x Spare Canopy
1x Screwdriver

Happymodel Mobula6 HDZero 1S 65mm Brushless HD FPV Whoop Drone - ELRS 2.4GHz