The pilot & videographer Ellis Van Jason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

Check out all our Digital BNF/PNP/RTFs and the rest of our IFlight Products!

HIGHLIGHTS:

6 inch drone re-engineered: This drone was specifically designed for 6 inch
H-shaped frame with robust middle section for less props in view while remaining stiffness
XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.
Built in BEC to directly power a gopro (no battery needed)
Hybrid motor design: This motor is optimized for 6 inch. Can be used with bi- blades (efficiency) and tri-blades (agility & trust).
Antenna mount: Solid antenna mount for less ocillations when using long antennas
Long back bone: Enough space up to 3000mAh 6S batteries
Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)
GPS: A high-end GPS is used to minimize the risk of failure during proximity flights
ESC: The drone consists iFlight's new ESCs with built-in spike absober for more reliability
9min flight time with 1800mAh 6S
9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion
Get Ellisvanjason's tune on ellisvanjason.com

Specifications:

Upper(middle) plate thickness: 2.5mm
Bottom plate thickness: 1.5mm
Total Dimensions: 254*254mm
Bottom to top distance: 22mm
Geometry: H-shaped frame
Top plate thickness: 2mm
Ellisvanjason 2506 motors
Gemfan 6032 propellers
Arm Thickness: 6mm
Takeoff Weight: Approx. 620 g
Diagonal Distance: 245mm
Max Speed: 130 Km/h (Manual Mode)
Maximum Takeoff Altitude: 5000 m
Max Hover Time: Approx. 8 mins
Max Flight Distance: 5 km
Max Wind Speed Resistance: 130 Km/H (Level 4)
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: 1 Antenna
GNSS: GPS +GALELEO
Video Transmission: DJI O3 Air Unit

Blitz F722 F7 Flight Controller Specifications:

Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
Smartaudio / IRC Tramp VTX protocol supported
Firmware target: IFLIGHT_BLITZ_F722
Motor outputs: 4x (SH1.0 connector)
Flash: 32MB (Blackbox flash)
I2C serial: SDA / SLA pads
Dimensions: 36.5*35 mm
Barometer: DPS310
OSD Chip: AT7456E
LED controller: Yes
MCU: STM32 F722
Beeper pad: Yes
Gyro: BMI270
Weight: 7.8g
UARTS: 6

Blitz E55A 4-in-1 2-6S ESC Specifications:

Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Mounting Holes: 30.5*30.5mm/Φ4mm
Target: IFLIGHT_BLITZ_G2
Supports 2-6S Lipo input
Current sensor: Yes
Constant: 55 Amps
Current rate: 200
Burst: 65 Amps
Weight: 15.3g
MCU： G071
BEC: No

Package Includes:

1 x IFlight BOB57 6" BNF/PNP HD 6S Cinematic Freestyle and Long Range Drone W/ DJI O3 FPV System - Chosen Receiver
2 x Antennas
2 x Battery pads
2 x 6" Propeller Set

Note:

All iFlight BNFs are tested before shipment to guarantee the highest quality.

Don't worry about tuning, we did that for you already! A basic PID- and Filter tuning was applied for a great flight experience!

To restore lost tunes or updates, please check our linked article on "Firmware/Factory Dumps"

Angle-Mode (self balancing level mode) is enabled by default to make sure your first flight doesn't end in a mess!

Please check our linked article on "How to disable Angle-Mode, activate Acro-Mode"

If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.

iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.

IFlight BOB57 6" BNF/PNP HD 6S Cinematic Freestyle and Long Range Drone W/ DJI O3 FPV System - Choose Receiver